loss power engine codes
Thread Starter
Joined: Mar 2010
Posts: 2
From: ky
loss power engine codes
I have 05 V6 5speed manual 39k miles. The problem I've had intermittenly. Hesitate and/or stall with loss of power. Check engine codes are P2106,P2135,P061B,P2104 & P2111. What is this ? How easy or hard to repair ? thanks for any help.
3rd Gear Member
Joined: Aug 2009
Posts: 723
From: Washington
Code P061B is a code indicating a torque calculation error by the PCM. The causes of this code are the same as the causes of code P2106. Code P2106 indicates that the Throttle Actuator Control (TAC) system is in a failure mode of "Force Limited Power" due to a concern of the Electronic Throttle Control (ETC) system or its components. This can be an effect of a problem in another vehicle computer system such as ABS / Stability Assist, the Instrument Cluster Module (ICM) or other systems. Codes P2104 and P2111 are throttle body related. In most case a throttle body failure will be the suspected cause of these codes. Code P2135 is caused when the PCM flags a concern indicating that the Throttle Position Sensor 1 and sensor 2 disagree by a calibrated limit. This is sometimes caused by a blockage of some kind in the throttle body or some other thing not allowing the throttle body to open or close all the way. The first thing I would do is check to make sure you don't have something stuck in there like a mouse. It's probably not likely but I'd check it out anyway to eliminate it. After that I would say you probably need a new throttle body. Hope this helps.
Joined: Jan 2025
Posts: 6
From: TX
Sorry I’m late
Code P061B is a code indicating a torque calculation error by the PCM. The causes of this code are the same as the causes of code P2106. Code P2106 indicates that the Throttle Actuator Control (TAC) system is in a failure mode of "Force Limited Power" due to a concern of the Electronic Throttle Control (ETC) system or its components. This can be an effect of a problem in another vehicle computer system such as ABS / Stability Assist, the Instrument Cluster Module (ICM) or other systems. Codes P2104 and P2111 are throttle body related. In most case a throttle body failure will be the suspected cause of these codes. Code P2135 is caused when the PCM flags a concern indicating that the Throttle Position Sensor 1 and sensor 2 disagree by a calibrated limit. This is sometimes caused by a blockage of some kind in the throttle body or some other thing not allowing the throttle body to open or close all the way. The first thing I would do is check to make sure you don't have something stuck in there like a mouse. It's probably not likely but I'd check it out anyway to eliminate it. After that I would say you probably need a new throttle body. Hope this helps.
Joined: Jan 2025
Posts: 6
From: TX
Sorry I’m late
Code P061B is a code indicating a torque calculation error by the PCM. The causes of this code are the same as the causes of code P2106. Code P2106 indicates that the Throttle Actuator Control (TAC) system is in a failure mode of "Force Limited Power" due to a concern of the Electronic Throttle Control (ETC) system or its components. This can be an effect of a problem in another vehicle computer system such as ABS / Stability Assist, the Instrument Cluster Module (ICM) or other systems. Codes P2104 and P2111 are throttle body related. In most case a throttle body failure will be the suspected cause of these codes. Code P2135 is caused when the PCM flags a concern indicating that the Throttle Position Sensor 1 and sensor 2 disagree by a calibrated limit. This is sometimes caused by a blockage of some kind in the throttle body or some other thing not allowing the throttle body to open or close all the way. The first thing I would do is check to make sure you don't have something stuck in there like a mouse. It's probably not likely but I'd check it out anyway to eliminate it. After that I would say you probably need a new throttle body. Hope this helps.
Thread
Thread Starter
Forum
Replies
Last Post
