2010 Style LED Harness hyper flash on D/S.
#1
2010 Style LED Harness hyper flash on D/S.
So I recently installed this 2010-2014 style LED sequential harness on my 2005 GT.
Well I have been having issues with hyper flashing ONLY on the driver side. And ONLY here and there while signaling. It doesn't happen when braking or using hazards. I also swapped the harnesses around to see if the problem was in there and it wasn't. I talked to the tech guy and he thinks it could either be the bulb, wiring issue, or the in dash flasher?? What you guys think?
Well I have been having issues with hyper flashing ONLY on the driver side. And ONLY here and there while signaling. It doesn't happen when braking or using hazards. I also swapped the harnesses around to see if the problem was in there and it wasn't. I talked to the tech guy and he thinks it could either be the bulb, wiring issue, or the in dash flasher?? What you guys think?
#2
I wonder if resistance needs to be added to the wiring to simluate a larger energy draw. I think the reason its hyper flashing is because the car thinks that a bulb or two is out because u r using "1/10th" the energy of the normal bulbs. I think diode dynamics had a device of some kind that you can plug in your fuse box to eliminate this. let me check
#3
http://www.diodedynamics.com/store/a...-flashers.html
Thats the address to their page. there is a lot of modules somehow they differ. but a few talk about working with LEDs to eliminate hyperblinking. let us know if it helps
http://www.diodedynamics.com/store/2...signal-flasher
Idk why this ^ one wouldnt work. are the gt500 plugs the same as v6 and gt?
Here is the resistor route:
http://www.diodedynamics.com/store/a...resistors.html
Thats the address to their page. there is a lot of modules somehow they differ. but a few talk about working with LEDs to eliminate hyperblinking. let us know if it helps
http://www.diodedynamics.com/store/2...signal-flasher
Idk why this ^ one wouldnt work. are the gt500 plugs the same as v6 and gt?
Here is the resistor route:
http://www.diodedynamics.com/store/a...resistors.html
Last edited by cema93; 04-03-2015 at 09:19 AM.
#4
But why would this only occur on JUST the driver's side and only the outside bulb no matter if I swap them around doesn't flash while sequencing? Hazard and brakes all light up just fine. I also have LED's with resistors in the front as well. I remember in the past with my previous sequential harness when the front resistor went bad it caused the tailights to black out after applying the turn signal. But sequentials themselves never need resistors to work.
Last edited by TekMan05; 04-06-2015 at 12:26 AM.
#5
Bump---
So I did some reading, and these cars don't have a relay for the flasher and it's all controlled by the smart junction box? Could this be related to that? Because I'm also noticing that my pass front signal isn't always illuminated.
So I did some reading, and these cars don't have a relay for the flasher and it's all controlled by the smart junction box? Could this be related to that? Because I'm also noticing that my pass front signal isn't always illuminated.
Thread
Thread Starter
Forum
Replies
Last Post
jwog666
Pipes, Boost & Juice
11
12-27-2021 08:09 PM
Galactic
Archive - Mustangs For Sale
10
04-29-2019 02:56 PM
Matt's 95 Stang
5.0L (1979-1995) Mustang
2
10-05-2015 07:16 AM
breaking
Audio/Visual Electronics
5
10-02-2015 01:27 PM