Convertible Tech This section is only for questions or information relating to a convertible. Questions about drivetrain modifications should still be posted in the engine specific sections.
Sponsored by:
Sponsored by:

Creaking Convertable

Old 08-14-2008, 12:07 AM
  #1  
KDL1
Thread Starter
 
KDL1's Avatar
 
Join Date: Aug 2008
Posts: 1
Default Creaking Convertable

We have an annoying creak in the framework of our 05 GT top. The lower sport springs we had installed have just made it worse. It doesn't matter if it's up or down. The only thing that somewhat quiets it is when the foam cover is on the top when it's down. Any suggestions would help as the dealer doesn't have a clue.
KDL1 is offline  
Old 08-14-2008, 07:50 PM
  #2  
ewgoetz
3rd Gear Member
 
ewgoetz's Avatar
 
Join Date: Nov 2007
Location: Venice, FL
Posts: 912
Default

get a can of white lithium grease and spray all the joints to start out.
ewgoetz is offline  
Old 08-24-2008, 09:49 PM
  #3  
kc5mhb
2nd Gear Member
 
kc5mhb's Avatar
 
Join Date: Dec 2007
Location: Louisiana
Posts: 229
Default

Does this TSB sound like your problem?


Convertible Top - Tension Cable Tick/Pop/Rattle

TSB 07-20-3

10/15/07
CONVERTIBLE TOP - TENSION CABLE NOISE -
BUILT BEFORE 12/1/2006

FORD:
2005-2007 Mustang

ISSUE
Some 2005-2007 Mustang Convertible vehicles built before 12/1/2006, may exhibit a tick, pop, rattle, snap, creak type noise that sounds like it originates above the front door glass area and/or convertible latches. The concern is caused by a stick/slip condition between the cable and the top. The cable runs from the number 1 bow to the number 5 bow and maintains the shape of the window opening. The noise resonates through the cable to the number 1 bow.

ACTION
Follow the Service Procedure steps to correct the condition.

SERVICE PROCEDURE

Replace both convertible top tension cables with revised service cables. The revised cables are incased within a teflon tube to prevent stick/slip to the convertible top material.
1. With roof in the closed and latched position, stand outside the vehicle with thumb placed under outer seam approximately 12" from the front edge of the convertible top, pull seam slightly outward/upward and release while listening for cable noise.

a. If stick/click, rubbing noise is heard go to Step 2.

b. If no noise is present continue with normal diagnosis.

2. Replace both convertible top tension cables per Workshop Manual, Section 501-18.


WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage
IMPORTANT : Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.

OPERATION DESCRIPTION TIME

072003A 2005-2007 Mustang 1.5 Hrs.
Convertible Built Before
12/1/2006: Replace Both
Convertible Top Tension
Cables, Includes Time For
Diagnosis

DEALER CODING

CONDITION
BASIC PART NO. CODE
7652806 41

Most dealers don't have a clue when it comes to tops. They sent mine out 4 times and had 2 tops replaced before the top people got it right. Then they tried to tell me that I put the top up while the car was in motion and it bent the arms. That is impossible due to a sensor that prevents the top motor from operating while the vehicle is in motion. I had a defective top assembly which by the way was also a TSB for my vehicle.

Last edited by kc5mhb; 08-24-2008 at 09:54 PM. Reason: Needed to add comment.
kc5mhb is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
cr620
V6 (1994-2004) Mustangs
2
10-03-2022 10:18 PM
lincolnshibuya
V6 (1994-2004) Mustangs
4
07-05-2020 03:05 AM
lovesilver
Members Mustangs
3
05-09-2019 09:18 PM
jerrytubes
2005-2014 Mustangs
2
10-23-2015 12:11 PM
guitarman376
4.6L (1996-2004 Modular) Mustang
0
09-30-2015 05:54 PM


Thread Tools
Search this Thread
Quick Reply: Creaking Convertable



All times are GMT -5. The time now is 08:10 AM.