Need advice on cams install and what psi to run with eibach drag launch kit - MustangForums.com

Go Back  MustangForums.com > Ford Mustang Tech > 4.6L (1996-2004 Modular) Mustang
Reload this Page >

Need advice on cams install and what psi to run with eibach drag launch kit

Notices
4.6L (1996-2004 Modular) Mustang Technical discussions on 1996-2004 4.6 Liter Modular Motors (2V and 4V) within.

Need advice on cams install and what psi to run with eibach drag launch kit

Reply

 
 
 
Old 02-15-2010, 10:45 PM
  #1  
Js04sILVerBullet
2nd Gear Member
Thread Starter
 
Join Date: Jan 2007
Location: Lincoln,NE
Posts: 420
Question Need advice on cams install and what psi to run with eibach drag launch kit

I have an 04 GT 5-speed with the mods done to it that are in my vid...numbers are on a "mustang dyno"

http://www.youtube.com/watch?v=IbPHFh0HxZw

I am wanting to upgrade to better cams next...will these be a good choice with my mods?With this kit it should be just about everything I need to install correctly?And will I have any problems running these with stock heads?

http://www.summitracing.com/parts/TFS-K51802002/

and lastly I am running a
Lakewood action traction lower control arms
Lakewood uppers
Lakewood struts and shocks
sub frame connectors
eibach drag launch spring kit with the airbag...what psi do you guys reccomend I run with this setup typically? oh and I do have M/T ET drag radials as well.

Last edited by Js04sILVerBullet; 02-15-2010 at 10:48 PM.
Js04sILVerBullet is offline  
Reply With Quote
Old 02-15-2010, 11:10 PM
  #2  
WannaBeGearHead
Go Texas!!!
 
Join Date: Jul 2009
Location: Lincoln, NE
Posts: 4,607
Default

I didn't know you were on this site. I'm over on SCR also.

Anyways, those cams in that kit, depending on the ICL, are most likely to cause PTV issues. I personally think there are better cams out there to be had rather than those.

Everything you would need comes in that kit.

Edit: come to think about it. Those cams are very close to the Hitech Stage 2 cams. I think you will be fine running those but again it still depends on the ICL. Have you looked around at other cams? Why did you choose the TF cams?

Last edited by WannaBeGearHead; 02-15-2010 at 11:15 PM.
WannaBeGearHead is offline  
Reply With Quote
Old 02-15-2010, 11:31 PM
  #3  
Js04sILVerBullet
2nd Gear Member
Thread Starter
 
Join Date: Jan 2007
Location: Lincoln,NE
Posts: 420
Default

The price is really why I am considering these.
I know Trickflow makes a good cam for a pushrod motor...so I thought why not consider these.

Other cams I have been looking at are cushman stage 2's.
Js04sILVerBullet is offline  
Reply With Quote
Old 02-15-2010, 11:40 PM
  #4  
WannaBeGearHead
Go Texas!!!
 
Join Date: Jul 2009
Location: Lincoln, NE
Posts: 4,607
Default

Well with the CMS Stage 2 cams or really any Stage 2 cam (minus MHS) you run into possible PTV issues which Nick at Modular Head Shop has measured to be only .005" with the CMS Stage 2.

Most people on here will tell you CMS, Hitech, Comp Stage 2. I would take a look over at MHS. Nick's cams don't require spring upgrades and you won't run into any PTV issues.

Last edited by WannaBeGearHead; 02-16-2010 at 12:08 AM.
WannaBeGearHead is offline  
Reply With Quote
Old 02-16-2010, 08:00 AM
  #5  
mrtstang
6th Gear Member
 
mrtstang's Avatar
 
Join Date: Jan 2007
Location: MI
Posts: 5,884
Default

Yeah, those TF stage 2's are a tight squeez imo. I would not take that chance. Besides, those specs are not ideal if you're running the stock PI heads. I assume you plan on staying with stock heads since you didn't state otherwise?

+1 on the MHS cams. Their stage 2's can be installed at advertised specs without having to worry about ptv clearance, and are designed for stock heads.
mrtstang is offline  
Reply With Quote
 
 
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Urambo Tauro
New Member Area
12
12-17-2016 04:30 PM
5.0pntydrpr
Classic Mustangs (Tech)
15
08-27-2015 11:26 PM
01moostanggt
4.6L (1996-2004 Modular) Mustang
8
08-17-2015 02:22 PM
ding56
Classic Mustangs (Tech)
3
08-14-2015 03:40 AM
djbigskrilla
2005-2014 Mustangs
13
08-11-2015 01:59 PM


Thread Tools
Search this Thread
Quick Reply: Need advice on cams install and what psi to run with eibach drag launch kit


Advertising
Featured Sponsors
Vendor Directory

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.